UK industrial valve sourcing, automation packages and practical application support

ALLWAY VALVESIndustrial valve supply & selection Request a Quote

Technical article

Valves for Snowmaking and Ice Rink Refrigeration Systems

  • Snowmaking valves live in a duty most industrial valves never see: charged with water at 20–40 bar one minute and expected to drain bone-dry before the temperature drops to −20°C, so every design decision is really a freeze-protection decision.
  • Ice-rink plant splits into a primary refrigerant circuit — anhydrous ammonia (R717) or CO2 (R744) at up to 40 bar for transcritical CO2 — and a secondary glycol or calcium-chloride brine loop at roughly 0 to −12°C feeding the floor, each demanding different valve metallurgy.
  • Sub-zero service pushes elastomer choice hard: standard nitrile (NBR) stiffens badly below −30°C, so low-temperature NBR, silicone or an FKM/FVMQ blend rated to −40 or −55°C is specified for seats and seals that must still seal after a night on an exposed mountain.

Few valve applications combine hydraulic abuse and thermal cruelty the way winter-sports systems do, and snowmaking valves sit at the sharp end of it. A machine-made snow network takes cold filtered water, pushes it to 20–40 bar through kilometres of buried and surface pipe, and atomises it against compressed air at fan guns and lances spread across a mountain where the ambient can be −15°C or colder. Get the valve selection or the drain philosophy wrong and you do not get a leak — you get a burst manifold and a lost operating night at the busiest time of the season.

Ice-rink refrigeration is the indoor cousin of the same problem. Instead of throwing water at the air you are pulling heat out of a concrete slab through a secondary brine or glycol loop, chilled by an ammonia or CO2 plant sitting in a machinery room governed by EN 378 and, for ammonia, the pressure-equipment and safety regime that comes with a toxic, flammable refrigerant. This article walks through both worlds: the on-mountain water and air valves, the pumping-station control, the rink primary and secondary circuits, and the cold-weather material choices that tie them together.

How snowmaking valves are loaded on the mountain

A modern fan-gun or lance system is a high-pressure water distribution network with a compressed-air overlay. Pump stations lift water from a reservoir or holding pond and boost it in stages, so the pipeline pressure at the base can sit at 40 bar (PN40) and still arrive at the top of a run at a workable 20–25 bar. That immediately rules out PN16 valve bodies for the trunk mains; you are specifying PN40 ductile iron or cast steel for isolation and PN40-rated ball or butterfly valves at the hydrant tappings.

The compressed-air side is lower pressure — typically 7–10 bar from screw compressors — but it is not benign. Air leaving a compressor carries heat and moisture, and any condensate that collects downstream of an air valve will freeze solid overnight. Air-line isolation and drain valves therefore need the same drain-down discipline as the water side, and the seat materials have to tolerate oil carry-over from the compressors.

Water quality matters more than people expect. Reservoir water carries grit, algae and the occasional stone that got past the intake screen. That abrasive load chews at soft seats and at any valve throttling a high pressure drop, which is why full-bore ball valves and resilient-seated butterfly valves dominate the isolation duty — they present no pockets to silt up and no exposed trim to erode.

Freeze protection and automatic drain-down

The single governing requirement across a snowmaking network is that every metre of pipe and every valve cavity must be able to empty completely when the system is shut down. Water left standing in a low point or a valve body will freeze, expand roughly 9% by volume, and split whatever contains it. Cast iron does not stretch to accommodate that; it fractures.

Designers handle this with a combination of continuous pipe fall to drainage low points, air-purge (blow-down) of the mains, and automatic drain valves at every trap. The classic device is the self-draining spring-loaded drain valve that stays open until line pressure rises above a set threshold — around 2–3 bar — then snaps shut, and reopens the moment the pump stops and pressure decays. That way the network drains itself the instant it is de-pressurised, with no operator on the hill at midnight.

Isolation valves in this service should be chosen for drainability. A full-bore ball valve mounted with the stem horizontal drains cleanly; the same valve stem-up traps a slug of water in the lower body cavity. It is the sort of detail that never shows on a P&ID but decides whether a valve survives the first hard frost. I have seen a whole hydrant assembly written off because someone installed the isolating ball valve with the drain plug uppermost.

Cavity over-pressure is the second freeze hazard. A closed ball or gate valve trapping liquid between its seats becomes a sealed vessel; as that trapped water cools and any residual pockets freeze, pressure spikes hard. Snowmaking ball valves are therefore usually specified with a self-relieving or vented seat, or with an upstream-relieving cavity, so trapped liquid can escape back to the line rather than jack the seats apart.

Hydrant valves and on-mountain distribution

The hydrant valve is the workhorse of the mountain. It is the tapping point where a snow gun connects to the buried main, and it has to be robust, drain automatically, and survive being buried under a season of snow and spring melt. Most are a heavy-duty variant of a post or pillar hydrant, with an integral drain that opens when the hydrant is closed so no water sits in the riser.

Hydrant bodies are typically ductile iron to EN-GJS-400 with a fusion-bonded epoxy or WRAS-approved coating inside and out, because they spend their life alternately submerged, frozen and thawed. The internal main valve is often a resilient-wedge design with an EPDM-faced wedge, giving bubble-tight closure at PN25–PN40 and no metal seat to corrode.

Downstream of the hydrant, the flexible hose to the gun is isolated by a quick-acting quarter-turn ball valve so an operator can swap a gun without draining a whole branch. These get cycled thousands of times a season by cold, gloved hands, so lever effort and low-temperature seat torque are real selection criteria — a PTFE-seated ball valve that turns sweetly at +20°C can be brutally stiff at −20°C.

Pumping station control

The pump house is where snowmaking looks like any other high-pressure water plant, and where the control valves earn their keep. Multistage centrifugal pumps feed the network, and the flow demanded swings wildly as guns are opened and closed across the mountain through the night. Something has to protect the pumps and hold a sensible header pressure.

Pump discharge protection uses non-slam check valves — nozzle or tilting-disc types — because a simple swing check slamming shut when a pump trips will send a water-hammer transient down a rigid, full pipeline and can burst it. A nozzle check with its short stroke and spring assist closes before flow reversal builds, keeping the surge pressure within the PN40 rating.

Header pressure is usually managed by a pressure-sustaining or pressure-reducing control valve — a diaphragm-actuated globe pattern — or increasingly by variable-speed drives on the pumps with a control valve as backstop. Where a hydraulic control valve is used, its pilot circuit and small-bore sensing lines are themselves a freeze risk, so the pump house is heated and the valve is drained if the building loses heat.

Filtration isolation matters here too. Self-cleaning strainers and the isolation valves around them protect every nozzle downstream; a 200–500 micron screen is typical, and the backwash valves that flush the strainer have to sequence reliably in cold conditions or the whole plant blinds off.

Ice-rink primary refrigerant valves: ammonia and CO2

Move indoors and the valve population changes completely. An ice-rink refrigeration plant is a mechanical refrigeration system, and under EN 378 and the F-Gas and safety rules the refrigerant choice drives everything. Two circuits dominate new build: anhydrous ammonia (R717) and carbon dioxide (R744), the latter increasingly run transcritical.

Ammonia (R717) service

Ammonia is efficient, cheap and has zero GWP, but it is toxic and flammable, and it is aggressive to copper and copper alloys. That single fact removes brass and bronze from the valve list entirely. Ammonia valves are steel or ductile iron with steel trim; forged-steel globe and angle valves to the refrigeration pattern, with back-seating stems and gland packing suited to ammonia, are standard on the plant.

Seat and seal materials for ammonia are PTFE and specific ammonia-compatible elastomers — EPDM and certain grades of neoprene tolerate it, while ordinary NBR and most FKM grades do not. Isolation is often forged-steel bellows-sealed globe valves where a leak-tight stem is critical, because any ammonia release in an occupied building is a life-safety event that trips the machinery-room detection and ventilation.

Pressure relief is not optional. Every section of ammonia plant that can be isolated with liquid in it needs relief protection, usually dual relief valves on a three-way changeover so one can be tested while the other stays in service, discharging to a safe location per the pressure-equipment and refrigeration-safety codes.

CO2 (R744) service

CO2 sidesteps the toxicity problem but replaces it with pressure. A transcritical CO2 plant runs gas-cooler pressures up to 90–120 bar, and even a subcritical or standstill condition sits far above ammonia pressures, so every valve is a high-pressure component. Bodies are forged steel or high-grade stainless, and the whole system, including standstill pressure after a long shutdown, has to be rated for it — standstill can reach the 60–70 bar saturation pressure at ambient.

CO2 valves must also cope with the risk of dry-ice formation. Throttle liquid CO2 too fast to atmosphere and it flashes to solid dry ice at −78°C, which can block a vent or jam a relief valve. Service and relief arrangements are designed with that in mind, and the low temperatures demand seat elastomers and body steels certified for cryogenic-adjacent duty.

Ice-rink secondary loop: glycol and brine valves

Between the refrigeration plant and the rink slab sits the secondary loop, and this is where most of the rink’s valve count lives. A secondary refrigerant — inhibited ethylene or propylene glycol, or a calcium-chloride or potassium-formate brine — is chilled to roughly −7 to −12°C and pumped through the pipe grid cast into the concrete floor to freeze and hold the ice.

The distribution manifolds feeding the floor pipes carry banks of isolation and balancing valves. Butterfly valves with EPDM liners suit glycol well; EPDM is the right elastomer here because it is compatible with glycol and holds up at the low secondary-loop temperature, whereas NBR would harden. For chloride brines the corrosion picture is harsher and stainless or specially coated valve internals are used, because calcium-chloride brine will pit ordinary carbon steel and even some stainless grades over time.

Balancing the floor is a real hydraulic exercise: the header valves are set so every circuit in the slab sees the same flow, otherwise you get soft patches and uneven ice. Fixed-orifice double-regulating valves or pressure-independent balancing valves (PICVs) do that job, and their settings are recorded at commissioning so the ice technician can reproduce them after any maintenance.

Because the secondary fluid never boils, the valves are conventional water-service designs rated for the low temperature and the fluid chemistry — there is no phase-change or high-pressure drama here, just the discipline of picking elastomers and metals that survive years of cold glycol without hardening, swelling or corroding.

Sub-zero material and elastomer selection

Cold is the thread running through every valve in both systems, and it attacks in two ways: it embrittles metals and it stiffens elastomers. On the metals side, ordinary grey cast iron and standard carbon steels lose toughness as temperature falls and can fracture in a brittle rather than ductile way, so exposed mountain valves lean on ductile (spheroidal-graphite) iron and, where impact toughness is charted, low-temperature carbon steels such as ASTM A352 LCB/LCC with verified Charpy values at the design minimum temperature.

Elastomers are the more common failure point. Every elastomer has a glass-transition temperature below which it goes hard and loses its ability to spring back and seal. Standard nitrile is comfortable to about −30°C; below that it needs a low-temperature NBR grade, and for the coldest exposed duty silicone (VMQ, good to −55°C or lower) or a fluorosilicone blend is chosen despite the cost. The trap is specifying a seal on chemical compatibility alone and forgetting the cold — an FKM seat perfect for the fluid may be a brick at −25°C.

For the ammonia plant the constraint flips to chemical compatibility first: EPDM and PTFE in, copper alloys and most FKM out. For chloride brines it is corrosion first, cold second. Writing a single elastomer spec across a whole site is a mistake; the mountain hydrant, the compressed-air drain, the ammonia bellows valve and the glycol butterfly each want a different material, and the discipline is matching each valve to its own worst case.

Seasonal commissioning and reliability in the cold

Snowmaking is brutally seasonal. The plant sits idle and drained through summer, then has to come alive reliably on the first cold snap. Commissioning each autumn is a valve-by-valve exercise: every automatic drain is checked for free movement, every hydrant is exercised, every isolation valve is stroked, and the whole network is pressure-tested and then deliberately drained to prove the drain-down actually works before the water is trusted to it in freezing weather.

Actuator and instrument protection is part of that. Pneumatic actuators on mountain valves need dry, heated instrument air or they will freeze internally; electric actuators need heaters and the right low-temperature rating on seals and lubricants. Grease matters — a bearing packed with summer-grade grease can seize a valve solid at −20°C, so low-temperature lubricants are specified on stems and gears.

For the rink, reliability is about continuity rather than season: an ice sheet represents days of cooling energy, and a stuck secondary valve or a leaking ammonia gland can take an arena out of service mid-event. Planned maintenance leans on the isolation philosophy — enough sectioning valves that a single circuit or manifold can be isolated, drained and worked on without dumping the whole floor — and on the relief-valve test regime the refrigeration codes demand.

The common lesson across both systems is that cold is not a footnote to the valve spec — it is the spec. Rate the body for the real standstill or pump pressure, pick the seat elastomer for the coldest night not the average day, insist on genuine drainability, and protect the actuators, and these valves will start every season and hold every event. Skip any one of those and the failure will find you at the worst possible moment.