UK industrial valve sourcing, automation packages and practical application support

ALLWAY VALVESIndustrial valve supply & selection Request a Quote

Technical article

Valves for Selective Catalytic Reduction and Ammonia Injection

  • SCR reactors run at roughly 300–400°C and are dosed to hold ammonia slip below 2–5 ppm; over-dosing forms ammonium bisulphate that fouls the catalyst and air heater.
  • Anhydrous ammonia is a liquefied gas at about 8.6 bar (20°C) with an IDLH near 300 ppm, so isolation valves must give ISO 5208 Rate A / ANSI FCI 70-2 Class VI shut-off plus a fail-closed excess-flow device.
  • The injection grid is balanced with individual throttling valves across 20–40 nozzle zones; a flow maldistribution of more than 5–10% widens the NOx and slip spread across the reactor face.

Selective catalytic reduction is one of the few emissions technologies where the valves are as much a safety system as a process one, and getting the scr ammonia valves wrong shows up as either a toxic release or a fouled, de-rated catalyst. The chemistry itself is simple — ammonia and nitrogen oxides react over a vanadia–titania or zeolite catalyst to make nitrogen and water — but the reagent is hazardous, the flue-gas side is hot and abrasive, and the whole thing has to trim continuously against a moving NOx load. This guide walks through the valve population on an SCR train, from the reagent storage boundary through flow control and the injection grid to the flue-gas dampers, and the material and safety rules that keep them reliable.

How SCR Works and Where the Valves Sit

In a high-dust SCR the reactor is placed between the economiser and the air heater, seeing flue gas at 320–400°C, which is the active window for the standard vanadium-pentoxide/tungsten-trioxide on titania catalyst. Below about 300°C the catalyst stops working and ammonium bisulphate condenses; above roughly 420°C the vanadia starts to sinter and lose activity. The valves therefore split into two worlds: a hot flue-gas side that is all dampers and isolation blades, and a reagent side that is precision flow control on a toxic or corrosive fluid.

The reagent side begins at storage, runs through a metering or flow-control skid, mixes with dilution air, and terminates at the ammonia injection grid (AIG) that sprays the ammonia–air mixture into the duct upstream of a static mixer. Each of those stages has its own valve duty. The control philosophy is usually feed-forward on boiler load or measured inlet NOx, trimmed by a feedback signal from the SCR outlet NOx analyser, so the main reagent control valve is stroking constantly and needs good rangeability.

Choosing the Reagent: Anhydrous, Aqueous or Urea

The reagent decision drives almost every valve specification downstream, so it is worth being explicit about the three routes. Anhydrous ammonia is 99.5%+ NH3 stored as a liquefied gas; it is the cheapest reagent per mole but the most hazardous, and in many jurisdictions storing it above threshold quantities pulls the site into major-accident regulation such as COMAH or OSHA PSM.

Aqueous ammonia at 19–29% concentration trades hazard for footprint. The vapour pressure is far lower, so storage and pipework are gentler, but you are now handling a corrosive alkaline solution and must vaporise it before injection, which adds heated dilution air and a vaporiser with its own control valves. Urea-to-ammonia systems — whether catalytic hydrolysis or the proprietary decomposition processes — store a benign 40–50% urea solution and generate ammonia on demand, eliminating bulk ammonia storage entirely at the cost of a reactor skid and more instrumentation.

Do not confuse SCR with SNCR here. Selective non-catalytic reduction injects urea or ammonia directly into the furnace at 850–1100°C with no catalyst, and its valves are coarser: it is a spray-lance and pump-recirculation duty rather than the fine, catalyst-protecting trim that SCR demands. A hybrid plant may run SNCR for bulk NOx removal and a trim SCR downstream, in which case you will see both valve populations on the same unit.

Ammonia Flow Control Valves

The heart of the reagent skid — often packaged as an ammonia flow control unit (AFCU) — is the main metering valve. On an anhydrous or vaporised-aqueous system this is a vapour-service control valve, typically a globe or a characterised segment-ball design, sized for wide rangeability because boiler load and NOx swing over a broad range. A rangeability of 50:1 or better matters; a valve that can only turn down to 20% of trim leaves you unable to dose cleanly at low load, where slip problems are worst.

I specify equal-percentage trim here almost every time. The pressure drop across the injection grid is roughly constant, so equal-percentage characteristic keeps the installed gain sensible across the range and stops the loop hunting at low flow. Seat leakage should be at least Class IV, and I prefer Class V on the control valve so that at zero demand the reactor is genuinely not being dosed — a weeping control valve puts uncontrolled ammonia into the grid and shows up as slip.

On aqueous liquid systems ahead of the vaporiser, the metering valve is a liquid-service globe or a small ball control valve, and cavitation is the thing to watch. Ammonia solution flashing across the trim is both an erosion problem and a control problem. Anti-cavitation trim or simply staging the pressure letdown solves it; sizing to keep the pressure recovery factor comfortable is cheaper than replacing eroded cages every outage.

The Ammonia Injection Grid and Balancing Valves

The AIG is where SCR performance is won or lost, and it is a valve-intensive component that engineers new to the technology consistently under-appreciate. A large grid splits the diluted ammonia flow into 20–40 or more individual lances, each feeding several nozzles across the duct cross-section. Each lance branch carries a manual balancing valve — usually a needle or a fine-throttling globe — so the injection profile can be tuned to match the incoming NOx and velocity distribution.

Commissioning the grid is a tuning exercise: you traverse the reactor outlet with a NOx and ammonia grid, then adjust the zone valves to flatten the NOx-removal and slip profile. A well-balanced grid holds the RMS maldistribution under about 5%; a lazy one runs 15–20% and forces you to over-dose the whole reactor to cover the worst cells, which drives up slip and ammonium bisulphate fouling. Those balancing valves need positive position retention — a locking device or a memory stop — because vibration will walk an unlocked needle valve off its setting over a run.

Purge and Anti-Fouling Valves

Grid lances plug. Fly ash migrates back up the nozzles, and ammonium salts condense in cool spots, so most designs fit soot-blowing or air-purge connections with dedicated isolation and check valves. A periodic compressed-air or steam purge keeps the nozzles clear, and the check valve on each purge line stops flue gas and ash tracking back into the clean air header. Skimp on these and you will be pulling lances at every outage.

Selecting SCR Ammonia Valves for Safety Isolation and Excess Flow

This is the duty where the specification tightens hardest. The isolation valves that form the boundary around the ammonia system have to give tight shut-off, fail to a safe state, and in the anhydrous case limit the consequences of a downstream line failure. The block valves at the storage battery limit and at the AFCU inlet/outlet are typically fire-safe ball valves to API 607 / API 6FA with Class VI or ISO 5208 Rate A seats, spring-return actuated to fail closed, and tied into the emergency shutdown system.

Excess-flow valves are the classic anhydrous-ammonia safeguard. Fitted at the tank liquid and vapour outlets, they are self-actuating devices that slam shut when flow exceeds a set point — the signature of a sheared line or hose failure. They are sized to pass normal maximum flow with margin but trip on the runaway flow of a full-bore rupture, and they are a code requirement in many ammonia storage standards. Do not confuse them with a control function; they do nothing in normal operation and exist purely for the pipe-break case.

Emergency isolation valves (EIVs) remotely operable from a safe location, together with excess-flow and back-flow check valves, make up the layered isolation scheme. I always insist on actual seat-leakage testing to the specified class on these valves rather than accepting a catalogue claim — on a toxic gas the difference between Class IV and Class VI is the difference between a detectable weep and a genuinely closed boundary. Relief valves protecting the trapped liquid legs between block valves matter too: liquid ammonia has a high thermal expansion coefficient, and a blocked-in sun-warmed line will hydraulically overpressure without thermal relief.

Dilution Air and Vaporisation Valves

Ammonia is never injected neat. It is diluted with air to typically 5% or less by volume, comfortably below the 15–28% flammable range, before it reaches the grid. That dilution air is moved by blowers with their own control and isolation dampers, and the air/ammonia ratio is a controlled variable — a ratio control valve or damper trims the ammonia into a measured air stream. Losing dilution air while ammonia keeps flowing is a defined trip condition, so the interlock between the air-side damper position and the ammonia flow control valve is safety-critical.

On aqueous and urea systems the vaporiser or hydrolyser adds heated-air or electric-heater control valves and the associated temperature-control loops. The vaporiser has to fully flash the solution; carryover of liquid droplets into the grid causes local over-concentration and corrosion. The control here is a temperature-to-flow cascade, and the vapour-line isolation valve downstream of the vaporiser should be rated for the elevated temperature and for wet ammonia at start-up.

High-Temperature Dampers on the Flue-Gas Path

The flue-gas side is dominated by dampers rather than valves. A reactor needs inlet and outlet isolation for catalyst change-out and for bypass during start-up before the gas reaches the minimum catalyst temperature. Guillotine and louvre dampers handle this at duct sizes measured in metres, in materials chosen for 400°C service and fly-ash abrasion — typically Corten or low-alloy steel blades with stainless or Inconel seals in the hotter, more corrosive zones.

Where zero leakage past the isolation is required for safe catalyst-layer entry, a double-louvre damper with seal air — a fan pressurising the cavity between two blade sets above duct pressure — provides a positive-pressure barrier so no flue gas reaches the person in the reactor. That seal-air fan and its dampers are part of the permit-to-work isolation, not a process nicety. Bypass dampers on economiser or reactor bypass ducts see thermal cycling and warping, so blade stiffening and expansion allowance in the frame are what keep them sealing over years of cycling.

Materials for Ammonia and Flue-Gas Service

Material selection splits cleanly by fluid. For dry anhydrous ammonia, carbon steel is entirely serviceable and is the workhorse for pipework and valve bodies — with one important caveat. Ammonia stress-corrosion cracking of carbon steel is real in the presence of oxygen and is aggravated by high-strength weldments, which is why ammonia storage practice limits oxygen contamination and often adds a small water content (around 0.2%) as an inhibitor. Keep valve body and bolting hardness within NACE-style limits and avoid unstress-relieved high-strength components on the anhydrous boundary.

Copper, brass, bronze and other copper alloys are forbidden on ammonia — ammonia attacks copper aggressively and forms cracking-prone complexes, so no bronze-trim valves, brass fittings or copper impulse lines anywhere on the reagent side. For aqueous ammonia the alkaline solution pushes you toward 304/316 stainless for wetted parts. Elastomer choice follows the same logic: EPDM and PTFE are compatible with ammonia, while nitrile and Viton are not the right seat and seal materials for this service.

On the flue-gas dampers the enemies are abrasion from fly ash and, at the cold end, acid dew-point corrosion from SO3. Blades in the hottest sections may be low-alloy steel; seals and sacrificial wear plates in stainless. If the SCR sits downstream of the air heater in a low-dust or tail-end arrangement the temperatures are lower and the acid corrosion risk higher, which shifts damper material selection toward higher alloys or coatings.

Leak Detection and Interlock Interfaces

No ammonia system is complete without gas detection wired into the valve interlocks. Fixed ammonia detectors around the storage, skid and grid areas alarm at low levels (often 25 ppm) and trip the emergency isolation valves and excess-flow scheme at higher levels. The valves have to be part of a tested safety loop, not just electrically capable of closing — that means documented SIL rating on the ESD path, proof-test intervals, and partial-stroke testing on the larger actuated isolation valves so you can prove they will move without a full shutdown.

The AIG and injection lines also carry their own detection because a plugged, corroding grid is a slow leak waiting to happen. The interlock matrix typically closes the ammonia flow control valve and the block valves on loss of dilution air, high ammonia detection, low flue-gas temperature (catalyst not up to window), or boiler trip. Designing those trip valves fail-closed with adequate spring margin, and confirming actuator sizing against the worst-case differential, is where a lot of retrofit projects cut corners and later regret it.

Maintenance and Common Failure Modes

The recurring problems are predictable. Injection-grid balancing valves drift off setting or plug, so the annual routine is a grid traverse and re-balance plus a nozzle clean; treat it as planned work, not a surprise. Ammonia flow control valves suffer trim wear and, on aqueous service, cavitation damage, so cage and plug inspection at each major outage keeps rangeability honest.

Isolation and excess-flow valves fail dangerously — that is, they can sit passed and untested until the day they are needed — so their proof testing is the non-negotiable item. Seat-leak verify the ESD block valves, function-test the excess-flow valves, and stroke-test the dampers on a defined schedule. On the flue side, damper seals wear and blades warp from thermal cycling; leakage past a bypass damper wastes reagent and lets un-treated gas slip past the catalyst.

One field aside worth passing on: the single most common cause of poor SCR performance I have seen is not the catalyst at all but a badly balanced or partly plugged injection grid combined with a control valve that cannot turn down at low load. Sort the grid valves and the reagent trim, and a tired catalyst will often still hit its NOx guarantee. Chase the catalyst first and you can spend a fortune solving the wrong problem.

Get the reagent choice, the flow control rangeability, the grid balancing and the safety isolation right, and an SCR is a genuinely reliable piece of kit. The valves are unglamorous, but on this system they are the difference between clean, controlled NOx reduction and either a toxic hazard or a fouled, underperforming reactor.