UK industrial valve sourcing, automation packages and practical application support

ALLWAY VALVESIndustrial valve supply & selection Request a Quote

Technical article

Valves for Hydrogen Service: Material Selection, Embrittlement, and the Green Hydrogen Challenge

Expert guide to valves for hydrogen service covering hydrogen embrittlement, ASME B31.12 material requirements, acceptable body and trim materials, green hydrogen electrolyser and compression valves, and fugitive emissions in H₂ service.

  • Hydrogen embrittlement is the primary material concern in hydrogen valve specification — high-strength steels, certain stainless grades, and some copper alloys are susceptible to hydrogen-induced cracking under pressure, and the consequence of a valve body crack in hydrogen service can be catastrophic.
  • The emerging green hydrogen economy is creating new valve engineering challenges — high-pressure electrolysers, hydrogen compression trains, and fuel cell systems require valves operating in pure hydrogen service, often at pressures and temperatures where the material selection rules are different from traditional petroleum hydrogen service.
  • Valve design for high-pressure hydrogen must account for both internal and external hydrogen environments — high-pressure hydrogen permeates through valve stem packing and seal materials that are perfectly adequate for other fluids, and external hydrogen accumulation near the valve creates fire and explosion risks that must inform the entire valve and instrumentation design.

Hydrogen is having a moment in the energy industry, and it deserves one — but it also deserves careful engineering respect. Hydrogen’s combination of very small molecular size (enabling rapid permeation through materials), its flammability range (4–75% in air — the widest of any common fuel), and the hydrogen embrittlement of high-strength steels makes it a genuinely demanding fluid for valve engineers. Let me explain the key considerations.

Hydrogen Embrittlement: The Core Material Challenge

Hydrogen embrittlement (HE) occurs when atomic hydrogen diffuses into a metal’s crystal lattice and causes a reduction in ductility and fracture toughness. The mechanism is complex — different theories (hydrogen enhanced localised plasticity, hydrogen enhanced decohesion) describe different aspects — but the engineering consequence is clear: a steel component that would normally fail by ductile fracture (with plastic deformation and warning signs) instead fails by brittle fracture (suddenly, with minimal plastic deformation and little warning).

HE risk is highest in: high-strength steels (yield strength >690 MPa is a typical threshold of concern); cold-worked austenitic stainless steels (work hardening increases susceptibility); ferritic steels in high-pressure hydrogen; and copper alloys at elevated temperatures.

HE risk is influenced by: hydrogen partial pressure (higher pressure = more hydrogen activity); temperature (peak susceptibility is typically around ambient temperature, 20–50°C — high temperature reduces susceptibility); stress level (combination of hydrogen and tensile stress is needed for embrittlement); and material defects or stress concentrations that act as hydrogen accumulation sites.

ASME B31.12: Hydrogen Piping and Pipeline Code

ASME B31.12 (Hydrogen Piping and Pipelines) is the primary US standard for hydrogen system design, including valve specification. It provides material qualification requirements specifically addressing hydrogen embrittlement, including:

  • Hardness limits for carbon and low-alloy steels: maximum Vickers hardness 250 HV (equivalent to approximately Rockwell B 100 or Brinell 237)
  • Controlled chemical composition limits to minimise hydrogen embrittlement susceptibility
  • Required fracture toughness testing (Charpy or J-integral) to demonstrate adequate toughness in the hydrogen environment
  • Restrictions on cold-worked austenitic stainless steel (any cold work above a defined limit must be solution annealed before use in high-pressure hydrogen)
  • Specific bolt and fastener requirements for hydrogen service

For valves used in hydrogen service, the materials of construction must comply with ASME B31.12 material qualifications or be specifically qualified through hydrogen pressure test data.

Acceptable Valve Materials for Hydrogen Service

Body and Bonnet Materials

  • Carbon steel (ASTM A216 WCB): acceptable for moderate-pressure hydrogen service (<200 bar) when hardness limits are met. At higher pressures, fracture toughness data is required.
  • 316L stainless steel (annealed): widely used for hydrogen service; good hydrogen compatibility; must be in annealed (not cold-worked) condition.
  • Duplex stainless steels: generally not recommended for high-pressure hydrogen — duplex steels have been shown to have higher hydrogen embrittlement susceptibility than austenitic grades.
  • Nickel alloys (Inconel 625, Incoloy 825): excellent hydrogen compatibility; used in hydrogen compression and storage systems at high pressure.
  • Titanium (Grade 2, Grade 5): excellent for ambient-temperature hydrogen service; very low hydrogen absorption at ambient temperature. Note: titanium absorbs hydrogen at elevated temperatures (>300°C) and becomes embrittled.

Trim and Stem Materials

  • 17-4PH stainless: acceptable if in H1150 condition (high-temperature heat treatment, low hardness); not acceptable in H900 or H1025 (high hardness, susceptible to HE)
  • 316L stems: generally acceptable; surface finish requirements for packing compatibility apply
  • Avoid high-strength bolting (B7 above certain hardness): use B7M (NACE-compliant, hardness-limited) for hydrogen service fasteners

Elastomer Seals and Packing

Elastomers in high-pressure hydrogen can experience Rapid Gas Decompression (RGD) failure — when pressure is rapidly reduced, dissolved hydrogen comes out of solution in the elastomer faster than it can diffuse out, creating internal bubbles that can cause blistering, cracking, or explosive decompression failure. Elastomers must be qualified for the specific hydrogen pressure and temperature conditions using hydrogen compatibility testing (ISO 23936 or equivalent).

PTFE packing is generally compatible with hydrogen and is the standard choice for hydrogen valve packing. Graphite packing is also compatible. Elastomeric O-rings require specific qualification.

Green Hydrogen: Electrolyser and High-Pressure Storage Valves

Green hydrogen — produced by electrolysis of water using renewable electricity — is produced at pressures of 30–80 bar in PEM (proton exchange membrane) electrolysers or 1–30 bar in alkaline electrolysers. The hydrogen is then compressed for storage and distribution to 200–700 bar for tube trailers, compressed gas storage, or hydrogen fuelling stations.

This creates a unique valve specification challenge at the high-pressure end:

  • Electrolysis outlet valves: pure hydrogen (very low impurity content compared to hydrogen from steam methane reforming in refineries); stainless steel or nickel alloy bodies; PTFE-seated ball or diaphragm valves for isolation
  • Compression train valves (30–700 bar): at these pressures, ASME B31.12 fracture toughness requirements become very demanding; most suppliers specify solid solution-annealed 316L or Inconel bodies; specialised PTFE or PEEK seats; pressure-rated stem seals tested to high-pressure hydrogen protocols
  • Hydrogen refuelling station dispenser valves (350–700 bar): perhaps the most demanding valve application in the green hydrogen supply chain; tiny valve bodies must cycle thousands of times, seal reliably, and be immune to hydrogen embrittlement; SAE J2600 and ISO 17268 define refuelling connector and valve requirements

Valve Design Features for Hydrogen Service

  • Minimise elastomeric seals: use metal-to-metal seats and PTFE/metal packing wherever possible to reduce RGD risk
  • Live-loaded packing: maintain constant packing stress despite thermal cycling and hydrogen-related packing relaxation; critical for valve stem fugitive emissions in hydrogen service
  • Fugitive emissions performance: hydrogen molecules are very small — they permeate through packing more readily than hydrocarbon molecules. ISO 15848 Class A testing is appropriate for critical hydrogen valve packing
  • Fire-safe design: hydrogen’s wide flammability range and invisible flame make fire-safe valve design critical; secondary metal seats are required when primary thermoplastic seats are used
  • ATEX/IECEx certification: all electrically-powered actuators in hydrogen service areas require appropriate hazardous area certification

The hydrogen economy is at an inflection point, and the valve industry is working hard to develop and qualify products for this demanding service. Engage with manufacturers who have specific hydrogen qualification data — don’t assume that a standard valve suitable for natural gas service is automatically acceptable for hydrogen service at equivalent pressure and temperature.