UK industrial valve sourcing, automation packages and practical application support

ALLWAY VALVESIndustrial valve supply & selection Request a Quote

Technical article

Relief Valve Discharge Systems: Flare Headers, Vent Manifolds and Tailpipe Design Engineering

Quick summary:

  • The relief valve discharge system — tailpipe, header, knockout drum, flare/vent stack — must be engineered as an integrated system, not designed in isolation from the relief valves it serves; improper tailpipe sizing creates excessive back pressure that degrades relief valve performance
  • Back pressure on conventional spring-loaded relief valves must not exceed 10% of set pressure for variable back pressure, or the valve must be upgraded to a balanced bellows or pilot-operated design capable of tolerating higher back pressure
  • Flare header design must accommodate worst-case simultaneous relief scenarios, account for liquid accumulation and liquid dropout, and ensure safe combustion conditions at the flare tip for all credible relief cases

The Relief Valve Discharge System — An Integrated Engineering Problem

A relief valve is not a stand-alone device. Its performance — the pressure at which it opens, the flow it can pass, and the back pressure it experiences — depends critically on the discharge system connected to its outlet. The tailpipe, relief header, knockout drum, and flare or vent stack are as much a part of the overpressure protection system as the relief valve itself. Design them poorly and you can make a correctly-sized, correctly-set relief valve fail to provide the protection it was sized to deliver.

This integrated perspective is mandated by API 520 Part II and API 521 — the primary standards governing relief system installation and disposal systems. These standards are explicit: the back pressure generated in the discharge system must be considered in the relief valve design, and the discharge system must be designed to handle the full rated relief flow without creating excessive back pressure, liquid holdups, or structural loads that compromise system integrity.

In practice, discharge system design is often treated as a secondary exercise — the relief valves are sized and located first, then a piping designer routes the discharge lines to the nearest header without rigorous analysis. The result is frequent cases where back pressure limits are exceeded, where condensate accumulates in headers and creates two-phase flow problems, or where structural loads from slug flow or waterhammer damage tailpipe supports and connections.

Tailpipe Design — The Connecting Pipe from Valve to Header

The tailpipe connects the relief valve outlet to the main relief header. It is the most critical pipe section in the discharge system because it experiences the highest pressure and the highest velocity at the onset of relief — and because its design directly determines the initial back pressure experienced by the relief valve during relief.

Key tailpipe design requirements:

No pockets (no low points that accumulate liquid): The tailpipe must slope continuously from the relief valve outlet to the header, without dips or horizontal sections that accumulate condensate. If liquid accumulates in the tailpipe and the relief valve lifts, the initial discharge must push the liquid slug out of the tailpipe before gas relief can occur. The pressure required to accelerate this liquid slug creates a transient back pressure spike that can suppress the relief valve’s opening — potentially catastrophic in a critical overpressure scenario. All relief valve tailpipes must slope at a minimum of 1:100 to the header, and any unavoidable low points must be provided with automatic drain pots.

No isolation valves in the tailpipe: An isolation valve between a relief valve and its discharge system creates an obvious and unacceptable safety risk — closing that valve prevents relief and removes the overpressure protection. API 521 prohibits isolation valves in the discharge path from a relief valve unless a redundant relief valve is provided on the same vessel and interlocking arrangements prevent the isolation of both relief valves simultaneously. Where isolation valves are provided for maintenance (to allow relief valve removal without process shutdown), car-seal open or lock-open arrangements with administrative controls are mandatory.

Support for reaction forces: When a relief valve opens, the discharge momentum creates a reaction force on the tailpipe — the downward force on the header pipe as the high-velocity gas stream enters. This force is proportional to mass flow rate and exit velocity, and must be calculated and accommodated in the piping support design. For large relief valves with high rated capacities, these reaction forces can be substantial — on large gas or steam relief valves at high pressure, reaction forces of several tonnes are not unusual. The tailpipe, header, and supporting steelwork must be designed to resist these forces without excessive deflection or structural failure.

Back Pressure Calculation and Limits

Back pressure on a relief valve is the pressure at the valve outlet during a relief event. It has two components:

Superimposed back pressure: The pressure existing in the discharge header under normal operating conditions, before the relief event. In a closed header connected to a flare system, this is the normal flare header pressure — typically 0.1-0.5 bar in most plant flare systems, but can be higher in complex networks. Superimposed back pressure acts on the disc of the relief valve at all times and affects the effective set pressure. For a conventional spring-loaded valve with set pressure 10 bar and 0.5 bar superimposed back pressure, the effective opening pressure is 9.5 bar (the spring is set to open when the inlet pressure exceeds the sum of set pressure minus back pressure).

Built-up back pressure: The pressure generated in the discharge system by the relief flow itself — the pressure at the valve outlet when the valve is flowing at its rated capacity. Built-up back pressure depends on the pipe size, length, fittings, flow rate, and gas properties. It is calculated by pressure drop analysis of the discharge piping from the valve outlet to the point where pressure is fixed (flare stack outlet, atmosphere).

For conventional spring-loaded relief valves: API 520 Part I requires that variable back pressure (built-up) does not exceed 10% of the set pressure. If calculated built-up back pressure exceeds this limit, the valve will “chatter” — repeatedly opening and closing — rather than flowing continuously at rated capacity. Chattering causes mechanical damage to the seat and disc, generates excessive noise, and fails to provide continuous overpressure protection. The solution is either to increase the tailpipe diameter (reducing velocity and pressure drop), or to switch to a balanced bellows or pilot-operated valve that can tolerate higher back pressure.

Relief Headers — Design Principles

The relief header collects discharge from multiple relief valves on the same plant area or unit and routes it to the disposal system (flare, vent, or thermal oxidiser). Header design requires analysis of the worst-case simultaneous relief scenario — the combination of relief valves that can all be discharging simultaneously during the design case.

Common header design cases: fire case (all vessels in the header connected to vessels in a fire area may lift simultaneously when fire engulfs the area), blocked outlet case (a single vessel’s relief — largest credible relief — into the header), utility failure case (cooling water failure releasing all condensers simultaneously). The worst-case combination of simultaneous reliefs determines the required header flow capacity and the resulting header back pressure.

Header sizing methodology: Calculate the required relief header flow using the worst-case scenario. Using the established header routing (with all lengths and fittings), perform a pressure drop analysis from the furthest relief valve outlet through the header to the flare knockout drum. Verify that the resulting back pressure at the furthest relief valve outlet does not exceed the limits for each relief valve type. If limits are exceeded, increase the header pipe diameter or revise the header routing to reduce pressure drop.

Liquid knockout provisions: Most relief headers include low-point knockout drums or knockout sections where liquid condensate can accumulate and be removed before the vapour stream reaches the flare stack. Liquid entering the flare header — from condensate in gas relief streams, from liquid relief valves, or from condensation on cold headers — must be removed before it reaches the flare tip. Liquid at the flare tip causes smoking, unstable flame, and potential liquid carryover that creates a fire hazard. The knockout drum must be sized for the maximum liquid flow in the design case and provided with a liquid level indicator and drain pump or gravity drain system.

Flare Stack Design — Combustion and Safety Requirements

The flare stack is the final disposal point for combustible vapour relief. It must combust the relief gas safely — with stable flame, adequate combustion efficiency, and without creating a ground-level hazard from flame impingement, hot gas plumes, or thermal radiation. API 521 Section 5 provides detailed guidance on flare system design.

Flare tip velocity: The exit velocity of gas from the flare tip must be sufficient to prevent flame burnback (flame propagating down into the flare tip at low flow) but below the blow-out velocity at which the flame lifts off the tip and extinguishes at high flow. Flare tip manufacturers provide design guidance on velocity windows for their specific tip designs. Most flare tips are designed for exit velocities of 30-100 m/s at maximum design flow.

Purge gas: A continuous purge gas flow (natural gas or nitrogen) is maintained through the flare header and tip at all times to prevent air ingress when the flare is not flowing. Air in the flare header creates an explosive mixture — if ignited, the resulting deflagration travels up the header and can damage or destroy equipment. The purge flow rate is calculated to maintain a minimum gas velocity throughout the header above the critical velocity for air ingress (typically 0.03-0.1 m/s).

Radiation analysis: At maximum design relief flow, the flare flame radiates significant heat energy to the surrounding area. API 521 defines allowable radiation levels for personnel (at manned areas), equipment (continuous and short-term), and property boundaries. The flare stack height must be sufficient to ensure that radiation levels at grade are below the allowable limits for the design case. This analysis determines minimum flare height — often the primary driver of flare stack cost.

The relief valve discharge system is one of those engineering topics where the interaction between components — relief valve, tailpipe, header, knockout drum, flare — creates complexity that cannot be managed by looking at each component in isolation. The engineer who understands the complete system, performs the integrated back pressure and flow analysis, and designs each component with awareness of how it affects the others will produce a relief system that is truly fit for its overpressure protection purpose.