UK industrial valve sourcing, automation packages and practical application support

ALLWAY VALVESIndustrial valve supply & selection Request a Quote

Technical article

Flange Faces and Bolting for Valves: Ratings, Torque and Assembly

  • Match the face to the rating: ASME B16.5 covers flanges to NPS 24 and B16.47 (Series A and B) covers NPS 26 to 60, while EN 1092-1 uses PN classes – a raised face suits Class 150 to 600, and ring-type joints (RTJ) take over from Class 900 upward and on API 6A wellhead duty.
  • Aim for a bolt preload of roughly 50 to 70 percent of the stud’s yield strength, applied in at least four cross-pattern passes (about 30 percent, 60 percent, 100 percent, then a final round-the-clock check) so the gasket seats evenly.
  • Never bolt a raised-face flange against a flat cast-iron flange: the unsupported overhang cracks the brittle casting. Use full-face gaskets and flat-face mating on grey iron, and reserve RTJ grooves for machined steel forgings only.

Where valve flange bolting actually leaks

Get the valve flange bolting wrong and it does not matter how good the trim, the seat or the actuator is – the plant loses containment at the joint. In more than two decades of witnessing hydrostatic tests and chasing weeping flanges on live plant, I have seen far more failures at the flange face than in the valve body itself. The joint is a system: face type, gasket, studs, nuts and the assembly sequence all have to agree, and a mismatch in any one of them shows up as a wet flange.

This guide walks through the three face types you will meet on valves – raised face, flat face and ring-type joint – how they map onto ASME and EN ratings, how to pick and grade the bolting, and how to torque or tension it so the gasket sees the load it was designed for. It closes with the two things that cause most site headaches: hot bolting and face damage.

Flange face types: RF, FF and RTJ

The face is the sealing geometry machined onto the flange. It dictates which gasket you can use and how much of the flange area carries the seating load. On valves you will encounter three in practice, and getting the pairing right is half the battle.

Raised face (RF)

The raised face is the workhorse. A small ring of material stands proud of the bolt circle – 1.6 mm (1/16 in) on Class 150 and 300, and 6.4 mm (1/4 in) on Class 400 and above – concentrating the bolt load onto the gasket rather than the whole flange face. That concentration is why RF flanges seal reliably across the bread-and-butter range of Class 150 to 600.

Finish matters more than most people credit. ASME B16.5 calls for a serrated spiral or concentric “stock finish” of roughly 3.2 to 6.3 micrometres Ra for soft and spiral-wound gaskets; that controlled roughness gives the gasket something to bite into. A face polished smooth by an over-enthusiastic fitter will actually leak, because a soft gasket has nothing to key against.

Flat face (FF)

A flat face has no raised ring – the entire face is one plane and the gasket is full-face, drilled for the bolts. Its home is grey cast-iron and other brittle-body valves. Bolting an RF flange to a flat cast-iron flange leaves the casting overhanging the raised face, and as you pull the joint up the bending moment cracks the flange, sometimes weeks later in service. On cast iron, flat face and a full-face gasket every time.

Ring-type joint (RTJ)

For high pressure and temperature – Class 900, 1500, 2500 and API 6A wellheads – the RTJ takes over. A solid metal ring, oval or octagonal in section (per ASME B16.20), seats into a machined groove in each flange and seals on line contact as the bolts coin it into the groove. The ring is deliberately softer than the flanges: soft iron, low-carbon or 304/316 stainless, chosen so it yields rather than damaging the groove.

RTJ joints are unforgiving of dirt and handling damage. A single nick on the groove seating surface, or a ring reused after it has been coined once, gives a leak path that no amount of extra torque will close. Fit new rings, and protect the grooves during storage – that is field discipline, not paranoia.

Pressure-temperature ratings: B16.5, B16.47 and EN 1092

Flanges are rated by class or PN, and the allowable pressure falls as temperature rises. ASME B16.5 governs NPS 1/2 through NPS 24 in Classes 150, 300, 400, 600, 900, 1500 and 2500. Above NPS 24, ASME B16.47 takes over – Series A (formerly MSS SP-44) and the more compact, lighter Series B (formerly API 605), which are not interchangeable, so confirm which series the mating flange is before you order.

The European system, EN 1092-1, ratings in PN – PN 6, 10, 16, 25, 40, 63, 100, 160, 250, 320, 400 – where the PN number is the approximate allowable pressure in bar at ambient. A Class 150 flange is broadly comparable to PN 20, and Class 300 to PN 50, but they are not drop-in equivalents: bolt circles, bolt counts and thicknesses differ, so you cannot bolt an ASME flange to an EN flange without an adaptor or a transition spool.

Read the rating tables, do not guess. A Class 300 carbon-steel (Group 1.1) flange rated 51.1 bar at 38°C is down to about 27.5 bar by 425°C. Design your bolt-up and your gasket choice around the actual service temperature, not the ambient headline figure.

Matching the gasket to the face

The gasket and the face are a pair; you do not choose one without the other. Full-face soft gaskets belong on flat faces. Raised faces take ring gaskets that sit inside the bolt circle – spiral-wound with an outer centring ring is the default across Class 150 to 600 process service, giving a good balance of recovery and blow-out resistance. Kammprofile (grooved metal core faced with graphite or PTFE) suits duties with thermal cycling where you want low seating stress and reusability.

RTJ grooves take only the matching ring – oval or octagonal, R-number to suit the flange. Do not try to seal an RTJ groove with a flat gasket, and do not fit an octagonal ring where the groove was cut for oval. The gasket seating stress (the m and y factors from ASME BPVC Section VIII, Division 1, Appendix 2) has to be met by the bolt load; a spiral-wound gasket needs far more seating stress than a soft sheet, which is exactly why undersized or under-torqued bolting weeps on spiral-wound joints.

Bolt and stud materials and grades

For flanged valve joints the standard fastener is a continuously threaded stud bolt with two heavy hex nuts, not a cap screw. The reference grades come from ASTM: A193 for bolting and A194 for nuts. B7 (chromium-molybdenum, quenched and tempered) is the default stud for most carbon and low-alloy service to about 400°C, paired with A194 Grade 2H nuts. That B7 / 2H combination covers the large majority of process flanges.

Move outside that window and the grade changes. For low temperature down to −100°C, A320 L7 with L7-compatible nuts (A194 Grade 4 or 7) gives the notch toughness B7 lacks. For higher temperatures and creep, B16 holds up better. In corrosive or chloride-bearing environments, B8/B8M (304/316 stainless, A193) resists attack but at much lower strength – a B8M Class 1 stud has well under half the yield of B7, so preload targets and torque values must be recalculated, never carried across.

A practical trap: mixing grades on one joint, or fitting stainless nuts on stainless studs without anti-seize, which galls and seizes on assembly. Always match nut grade to stud grade, apply a compatible thread lubricant, and record the friction factor you assumed – because that factor is what turns your torque figure into actual bolt tension.

Torque, tension and target preload

The whole point of bolting is preload – the tension locked into the stud that holds the gasket compressed and keeps the joint from separating under pressure and thermal load. A sensible target is 50 to 70 percent of the stud’s specified minimum yield, high enough to seat a spiral-wound gasket and resist blow-out, low enough to leave margin for thermal and service loads. Too little and the joint leaks; too much and you crush the gasket or yield the stud.

Torque is only a proxy for tension, and a poor one. The classic short-form relation is T = K × D × F, where T is torque, D is nominal bolt diameter, F is target preload and K is the nut factor – typically around 0.20 dry, dropping to 0.12 to 0.15 with a good anti-seize. Because as little as 10 to 20 percent of the applied torque actually becomes bolt tension – the rest is lost to thread and nut-face friction – a wrong assumption about K swings your real preload wildly. That friction scatter is why torque-controlled joints show ±20 to 30 percent preload variation across the bolt pattern.

Consult the joint’s bolting table or a recognised procedure (ASME PCC-1 gives a full method) for the target torque; do not eyeball it. And calibrate the wrench – an out-of-cal click wrench is worse than useless because it lies with confidence.

Cross-pattern tightening and controlled bolting

Even the right total load fails if you apply it in the wrong order. Bolts must be brought up gradually in a criss-cross (star) pattern so the gasket compresses evenly and the flanges stay parallel. Snug the joint first, check flange gap all round with feeler gauges, then work up in passes. A typical controlled-bolting sequence looks like this:

PassTarget torquePatternPurpose
SnugHand-tight to ~20%Cross (star)Align flanges, close the gap evenly
1~30%Cross (star)Begin uniform gasket seating
2~60%Cross (star)Build preload without local crush
3100%Cross (star)Reach target preload
4100%Rotational (clockwise)Final check pass – confirm no bolt lags

Watch flange parallelism throughout: measure the gap at four points and keep it within roughly 0.4 to 0.8 mm all round. A cocked flange means one side is over-loaded and the other is barely sealing – back off and re-seat rather than chasing the leak with more torque. On critical joints, log every bolt and every pass; that record is what tells you, six months later, whether a weep is an assembly error or a gasket relaxation issue.

Hydraulic tensioning versus torquing

On large-diameter, high-class and RTJ joints, torque wrenching becomes unreliable – the friction losses are too big and the reaction forces too awkward. Hydraulic tensioning sidesteps the friction problem entirely: a tensioner stretches the stud axially with a known hydraulic force, you run the nut down finger-tight against the flange, then release – the recovered stretch is the preload. Because you are measuring force directly rather than through a friction-laden torque, accuracy improves to around ±10 percent or better.

The catch is load transfer and embedment. When the tensioner lets go, the stud shortens slightly as the nut and threads bed in, so you lose some preload – on 100 percent tensioning you compensate with a load factor, or you tension every stud simultaneously with a bolt-tensioning bridge to keep the joint even. Tensioning also needs enough stud protruding above the nut to grip, so specify longer studs when the joint is designed for tensioning. It is the right tool for big joints, but it has to be planned in, not improvised on the day.

Hot bolting: proceed with caution

Hot bolting – retightening or replacing bolts on a joint that is live and at temperature – is one of the highest-risk routine tasks on a plant, and it is done far too casually. Joints relax as they heat up: gaskets creep, studs stretch differentially, and a flange that was tight cold can weep hot. Retorquing at temperature restores preload, but doing it on a pressurised, hot, possibly hydrocarbon-filled joint is a controlled operation, never a quick nip-up.

The cardinal rules: work one stud at a time, never slack more than one bolt on a live joint, and follow a written procedure with the line depressurised where at all possible. Replacing studs one-by-one on a pressurised joint is only ever justified with a full risk assessment, a defined maximum number of bolts removed at once, and an escape plan if it starts to leak. If the service is toxic, flammable or above about 200°C, the default answer is to isolate and depressurise first – the joint can wait, your fitter’s hands cannot.

Flange face damage and repair

Most persistent flange leaks trace back to a damaged face, not a bad gasket. Radial scratches across the serrations are the classic killer – a single tool-mark running from bore to bolt circle gives the fluid a channel straight across the seal. Corrosion pitting, erosion near the bore, and coined or nicked RTJ grooves are the other usual suspects. Inspect and clean every face before you fit a gasket; do not assume a face is good because it looks flat.

Light circumferential scratches within the serrated finish can be left; radial defects cannot. On-site flange facing machines can re-cut a raised face and restore the spiral serration in place, which is far quicker than pulling the valve. RTJ grooves can be re-machined to a larger R-number ring if there is metal to spare. After any repair, verify the finish (3.2 to 6.3 micrometres Ra for standard gaskets) and re-check the face flatness – a re-cut face that is not perpendicular to the bore will leak just as surely as the original defect.

Leak troubleshooting: a field checklist

When a flanged valve joint weeps, resist the urge to just crank the bolts. Over-torquing a leaking joint often makes it worse by crushing the gasket or bending the flange. Work through the causes in order. Was the preload right – correct torque, calibrated wrench, right nut factor? Was the pattern followed and the flange parallel? Is the gasket the correct type and rating for the face, and was it centred?

Then look at the hardware: face finish and damage, groove condition on RTJ, stud and nut grade, and whether anything relaxed after thermal cycling. A joint that sealed cold and leaks hot points to gasket creep or differential expansion – a candidate for a controlled hot re-torque or a Kammprofile gasket with better recovery. A joint that never sealed points to assembly: wrong load, wrong pattern, damaged face or the wrong gasket entirely.

Sound valve flange bolting is unglamorous and entirely procedural, and that is exactly why it gets skipped. Match the face to the rating and the gasket, grade the studs to the service, hit a real preload in a controlled cross-pattern, and treat hot bolting and face damage with the respect they demand. Do that and the joint becomes the most boring part of the valve – which, on a live plant, is precisely what you want.